Vertical Drills Drilling

2003 - Lodril DH100 Vertical Drill()

FOB Redding CA

2003 - Lodril DH84-60 Vertical Drill()

2003 loDril DH84-60 mtd on 2003 Hitachi 450LC. Isuzu Diesel Engine, Expandable Tracks, 11,989 Hours. Unit is very good condition. Tight, Work Ready Machine. $149,500

2014 - Little Beaver HYDTB11H Vertical Drill()

Little Beaver’s Towable Hydraulic Earth Drill is compact and versatile. The unit’s streamlined towing system makes it easy to move from one project to the next, and its powerful hydraulic drive will have yo ..... read more

2021 - Link-Belt 750 X4 Vertical Drill()

2021 Link-Belt 750X4 with Indeco HP16000FS Hydraulic Breaker. 1688 Hours. Call for Price.

2019 - Junjin JD1400E Vertical Drill()

YH135 Drifter, Cummins QSL9 Tier 4 Final, GHH-Rand 490CFM @ 150PSI, Onboard Air Compressor, 125 Total Hours, Like New. Sold with New Warranty.

2017 - Junjin JD800ENC Vertical Drill()

YH80A Drifter* 20'ft lead rod long boom. (or standard boom is available)* Cummins Tier 3 Diesel Engine* Dust Collector Single Grousers Extendable Boom This unit comes standard with a 20’ft boom. As a special ..... read more

2019 - Junjin JD800ENC Vertical Drill()

YH80A Hydraulic Drifter **Tier 3 Diesel Engine Machine, NO DEF Fluid & NO Regen System. Built December 2018, This machine was sold new & put into service August 2019 year. Engine: Cummins QSB6.7 – Tier III Se ..... read more

2019 - Junjin JD800ENC Vertical Drill()

YH80A Hydraulic Drifter **Tier 3 Diesel Engine Machine, NO DEF Fluid & NO Regen System. Built December 2018, This machine was sold new & put into service August 2019 year. Engine: Cummins QSB6.7 – Tier III Se ..... read more

2018 - Junjin JD800E Vertical Drill()

2018 Junjin JD800EII 1,650 Engine Hours 1,773 Percussion Hours Contact for more details

Joy MS4ES Vertical Drill()

3.5” – 4.5” Inch Class* CAT 3306 Diesel Engine* Extendable Boom* Water Injection Approx. 4500 total hours

2000 - Joy MS4ES Vertical Drill()

2.5 - 3.5 Inch Class* CAT 3306 Engine* On board, 900CFM Air Compressor* Dual Boom Controls VCR Drifter, 20 Ft Mast/ Tower Extendable Boom Dust Collector Water Injection

1990 - Ingersoll Rand R10071 Vertical Drill()

Ingersoll Rand LM100 Vertical Drill()

2006 - Ingersoll Rand ECM720 Vertical Drill()

**DRIFTER ONLY** - HC200A Drifter - Excellent condition - Very low hours since new

2007 - Ingersoll Rand ECM720 Vertical Drill()

4.5” – 5.5” Inch Class* CAT C11 Diesel Engine* HC200A Drifter set up for GT60 Rods* Caterpillar C11 Diesel Engine Montabert HC200A drifter. Recent new hydraulic Pump Aprox. 11800 total frame hours Unit is ..... read more

2007 - Ingersoll Rand ECM720 Vertical Drill()

Montabert HC200A Drifter - '0' hours on fresh service CAT Engine Set up for 60mm drill steel Onboard Air of 480 CFM @ 150 PSI 5500 total frame hours 2012 percussion hours w/ '0' hours on new service. PRICED TO ..... read more

2008 - Ingersoll Rand ECM720 Vertical Drill()

4.5 - 5.5 Inch Class* Montabert HC200A Drifter* Cat C11 Engine* Set up for 60mm drill steel Only 3570 Total Hours

1996 - Ingersoll Rand ECM690 Vertical Drill()

4.5” – 5.5” Inch Class* CATERPILLAR Diesel Engine* YH Series Drifter* YH110V Hydraulic Drifter Set up for T51 CAT 3306 Diesel Engine Extendable Boom Rod Changer

1999 - Ingersoll Rand ECM690 Vertical Drill()

3.5 - 4.5 Inch Class* HC200A Drifter* CATERPILLAR 3306 Diesel Engine* Extendable Boom Onboard Ingersoll-Rand 420 CFM @ 150 PSI Air Compressor Rod Changer Ready to ROCK & ROLL!

2002 - Ingersoll Rand ECM680 Vertical Drill()

3.5” – 4.5” Inch Class* HC150 Drifter * Set up for T51* Cummins Diesel Engine

2011 - Ingersoll Rand ECM660 IV Vertical Drill()

3.5 - 4.5 Inch Class* HC158 Drifter* Cummins Tier 3 Diesel Engine*

2011 - Ingersoll Rand ECM660 IV Vertical Drill()

3.5 - 4.5 Inch Class* HC158 Drifter* 5950 total frame hours* 844 percussion hours Overall unit is in excellent condition. Will be cleaned at time of sale.

2004 - Ingersoll Rand ECM660 III Vertical Drill()

3.5 - 4.5 Inch Class* Montabert HC160 Drifter* Very Well Maintained Unit* 7036 Total Frame Hours 2251 Percussion Hours

2002 - Ingersoll Rand ECM660 II Vertical Drill()

3.5 - 4.5 Inch Class* HCR120 Drifter w/ 2287 Percussion Hours* Cummins Diesel w/ 5,828 Hours* Enclosed Cab w/ AC Set Up for T51 Rod Changer w/ One-Lever Control

2014 - Ingersoll Rand ECM660 Vertical Drill()

3.5 - 4.5 Inch Class* HC 158 Drifter* Cummins QSL9 Diesel* Extendible boom 1430 hours Back-Up Alarm Warning Horn Accumulator Charge Kit Drifter Hour Meter Air Conditioned and Heated 2D Digital Angle Indicator A ..... read more

1997 - Ingersoll Rand ECM590 Vertical Drill()

- Equipped with YH80A Drifter - Ready to work - Repairs needed are one door with broken hinges - Fuel stop solenoid - This machine has a new air end and has less than 200 hours on hydraulic pump

1999 - Ingersoll Rand ECM590 Vertical Drill()

- Equipped with YH80A Drifter -Only known issue is the engine Boggs down under a hydraulic pressure load everything works as intended but noticeable lack of performance due to lower engine rpm's . Possible fuel ..... read more

2000 - Ingersoll Rand ECM590 Vertical Drill()

- Equipped with YH80A Drifter - Unit needs nothing is currently running on a job at this time. - Has newer paint job - Manual rod changer - Long boom

2002 - Ingersoll Rand ECM590 Vertical Drill()

2002 Ingersoll-Rand ECM590 • Set up for T51, looking for extra rods/bits. Will confirm • Cummins Engine Rebuilt in 2017 w/ 3,098 Hours • 3,536 Drifter Hours • YH80 Hammer(Rebuilt) • EXW: New Jersey

2003 - Ingersoll Rand ECM590 Vertical Drill()

- Comes with YH70, not currently installed but will be mounted for transport - Batteries need charging or replaced so could not stand machine up at time of photos. - Missing wall and doors need to be reattached ..... read more

2004 - Ingersoll Rand ECM590 Vertical Drill()

- Comes with YH70 not currently installed but will be mounted for transport - This unit has tracking issues will move but unknown if it's the final drives or hydraulic motors. - Hammer needs to be mounted back ..... read more

2004 - Ingersoll Rand ECM590 Vertical Drill()

- Equipped with YH80A Drifter - Mechanic believes there is a broken pin in the fuel injection pump machine will idle but will not idle up. - Other repairs needed are inoperable fuel stop solenoid

2005 - Ingersoll Rand ECM590 Vertical Drill()

2005 Ingersol Rand ECM590 8.3 Cummins Engine YH80 Drifter Set Up For T45 7,228 Engine Hours 3,564 Drifter Hours $49,500 Contact for more details

2005 - Ingersoll Rand ECM590 Vertical Drill()

- Equipped with YH80A - Ready to work - Repairs needed are inoperable fuel stop solenoid

2006 - Ingersoll Rand ECM590 Vertical Drill()

- Equipped with YH80A Drifter - Repairs needed or in the process of being repaired - Dust collector top new part has been fabricated need's installed - Rod changer arm is broken have new parts to replace purcha ..... read more

2007 - Ingersoll Rand ECM590 Vertical Drill()

2007 Copco/IR ECM 590 • Set up for T45 • YH-80 Hammer • Good overall working condition • Currently on a job but available

2005 - Ingersoll Rand ECM585 Vertical Drill()

2.5 - 3.5 Inch Class* Montabert HC109 Drifter* Excellent Condition* Engine Hours 5416.2 Percussion has ONLY **933 Total Percussion hours since new*** HC109 Drifter was last rebuilt June 2015 – last rebuilt @ ..... read more

2002 - Ingersoll Rand ECM580 Vertical Drill()

3.5” – 4.5” Inch Class* HC80RP Drifter* Cummins Diesel Engine* Extendable Boom 8130 Engine Hours Water Injection Dust Collector Enclosed Operators Cabin Montabert HC80RP Drifter

1997 - Ingersoll Rand ECM570 Vertical Drill()

2.5 - 3.5 Inch Class* Montabert HC80 Drifter* Cummins Diesel Engine*

1998 - Ingersoll Rand ECM570 Vertical Drill()

1998 Ingersoll Rand ECM570 Overall good condition relative to age Needs hose from boom to dust collector

2000 - Ingersoll Rand ECM490 Vertical Drill()

- Cummins 6CT8.3 - Tier 2 - 200CFM/140PSI Air - YH70 Drifter - Setup for T38 - 12,667 engine hours - Drifter Rebuild @ 12,518 Hours - New feed chain & sprockets @ 12,348 hours - 1,000 hour service done @ 12,667 ..... read more

2005 - Ingersoll Rand ECM370 Vertical Drill()

VL 140 Drifter Dual Boom Controls - Rare Option to Have Dust collector Water Injection Extendable Boom Hydraulic Centralizers

Ingersoll Rand ECM350 Vertical Drill()

2.5 - 3.5 Inch Class* VL140 Drifter* Comes with 3 Air Compressors* This is a Complete Drill Package with 3 Ingersoll-Rand Portable Air Compressors

1979 - Ingersoll Rand ECM350 Vertical Drill()

1997 - Ingersoll Rand DMLXL1200 Vertical Drill()

1997 INGERSOLL-RAND DMLXL1200 S/N 7239 CUMMINS ENGINE N14 IN-LINE 6 CYLINDER DIESEL WE HAVE BEEN DOING A LOT OF REPAIR ON THIS DRILL CHANGING POSSIBLY 20 HOSES IT SOUND PEFECT. WE HAVE SPEND APPROX 70,000 ON IT ..... read more

1995 - Ingersoll Rand DMLHP1250 Vertical Drill()

1995 DML HIGH PRESSURE DRILL S/N 3954 HAS 10949 HOURS THIS DRILL IS EQUIPPED WITH HR2.5 AIR COMPRESSOR @1800RPM=1070, @2100RPM=1250 ACFM, 350 PSI AIR COMPRESSOR PARTS NUMBER SX58357409/ S/N 751U12SNG1/ 26583642 ..... read more

1997 - Ingersoll Rand Dmlsp Vertical Drill()

DTH Class* Single Pass Drill Rig - 55'ft - 60'ft Mast* Cummins QSK19 Diesel Engine* High Pressure - IR HR2.5 - 1050 CFM @ 350 PSI Onboard Air Compressor CAT 330L&S Undercarriage

1997 - Ingersoll Rand DML1200 Vertical Drill()

1997 Ingersoll-Rand DML-LP 1200 S/N 7302 Cummins, A/C cab, 35 ft mast, 30 ft drill stem, dust collector, carousel, auto rod changer, 1200 cfm x 110 psi air comp, hyd stabilizers, fire suppression, fast fuel Jus ..... read more

1993 - Ingersoll Rand DML Vertical Drill()

4.5 - 5.5 Inch Class* CAT 3412 Diesel Engine w/ Only 1,500 Hours Since Rebuild* Runs 30"ft Drill Steel* High Pressure Unit w/ On-Board IR HR2 1050 CFM / 350 PSI New Pump Drive and Double Motor Spur Gear Head

1997 - Ingersoll Rand DML Vertical Drill()

Cummins N14, 1200XL compressor, 5-1/2” x30’ steel, dust collector, good working condition