search

Ingersoll-Rand VR642C Telehandler

EROPS HEAT 4X4 4-WHEEL STEER FRONT OUT RIGGERS CARRIAGE TILT 42' 6000LB 13.00-24 RUBBER FOAM FILLED CUMMINS DSL GOOD CONDITION

Ingersoll-Rand VR1056C Telehandler

Ingersoll-Rand 1056C for Sale showing just over 6600 hours on it, a clean looking machine. Powered by a Cummins engine gives it lots of power to reach up to the max height of 56 feet. machine has good tires on ..... read more

Ingersoll-Rand VR1056 Telehandler

MONTACARGAS TELESCOPICO, CON MOTOR CUMMINS B3.9-C A DIESEL 4 CILINDROS DE 110 HP. MARCA EN HORAS 8,420, 4X4, CAP DE 10,000 LBS. PICOS DE 5 FT DE LARGO X 6 PULGADAS DE ANCHO, ALCANCE DE 44.5 FT. NEUMATICOS 13.00 ..... read more

2004 - Ingersoll-Rand T4BH Vertical Drill

Cumins QSX15, 1070/350 HR2.5, dust collector, set up for 4-1/2" x 30' steel

1979 - Ingersoll-Rand SP56 Padfoot Compactor

1979 IR SP56 84" Sheepsfoot Vibratory Roller - Rear wheel and Drum Drive - Detroit Engine - Hi-Low Hydrostatic Drive - ROPS - Good tires - Good center Joint - Vibratory and drive system work good - 26,000lb Op. ..... read more

Ingersoll-Rand SD77F Padfoot Compactor

COMPACTADOR PATA DE CABRA INGERSOLL RAND SD77F, CON MOTOR CUMMINS B3.9 A DIESEL 4 CILINDROS DE 95 HP, CON TURBO, CON TRANSMISION HS, RODILLO DE 66 PULGADAS, NEUMATICOS 14.9-24, PESO 17,930 LBS

1995 - Ingersoll-Rand SD70F Padfoot Compactor

COMPACTADOR PATA DE CABRA EN MANTENIMIENTO CON MOTOR CUMMINS 4BT3.9C. DE 92 HP CON TURBO, RODILLO DE 66 PULGADAS, NEUMATICOS 14.9-24, PESA 15,100 LBS

1999 - Ingersoll-Rand SD70DA Drum Compactor

COMPACTADOR DE RODILLO LISO, EN MANTENIMIENTO CON MOTOR CUMMINS 4BT3.9C DE 92 HP. MARCA EN HORAS 8, 659, RODILLO DE 66 PULGADAS, NEUMÁTICOS 13.00-24 NHS, PESA 15,330 LBS

2007 - Ingersoll-Rand SD45D Drum Compactor

2007 Ingersoll-Rand SD45D 54: Smooth Drum Roller W/ Pad Shell kit. 2649 Verified Hours (Meter Replaced at 2649 Hours) Fully Serviced, Runs Excellent, Ready to Work

Ingersoll-Rand SD25D Drum Compactor

CON MOTOR KUBOTA V2203-M 4 CILINDROS DE 44 HP, RODILLO COMPACTADOR DE 42 PULGADAS, PESA 5,850 LBS

2003 - Ingersoll-Rand SD150D Drum Compactor

The Dynapac CC422 is a compact, double-drum vibratory roller used in asphalt compaction. It has a powerful engine with a high compaction force that allows it to efficiently compact even the toughest materials. ..... read more

2005 - Ingersoll-Rand SD100F Padfoot Compactor

84 INCH PADFOOT, CAB, HEATER, AIR CONDITIONING, GOOD GLASS, CUMMINS ENGINE, 23.1X26 DRIVE TIRES, GOOD PAINT AND COSMETICS

1999 - Ingersoll-Rand SD100F Padfoot Compactor

CON MOTOR A DIESEL CUMMINS B3.9C, DE 125 HP, CON TURBO, MARCA EN HORAS 2,219, RODILLO DE 84 PULGADAS, PALA DE 102 PULGADAS, LLANTAS 23.1-26, PESO 26,100 LBS

2006 - Ingersoll-Rand SD100D Drum Compactor

CAB, HEATER. AIR CONDITIONING, CUMMINS 3.9 TURBO CHARGED ENGINE, 84" SMOOTH DRUM, SCRAPER BARS, 23.1X26 TIRES, GOOD GLASS, PAINT,AND COSMETICS, PAD FOOT AVAILABLE AT ADDITIONAL COST, AVAILABLE FOR RENT

2015 - Ingersoll-Rand SD100D Drum Compactor

Machinery Trader Group Co., Ltd one of the biggest used construction machinery supplier in China.We are specialized in used construction machine such as wheel loader, bulldozer, road roller, grader, crane, exca ..... read more

1996 - Ingersoll-Rand SD100D Drum Compactor

Open ROPS canopy 84” smooth drum, drum drive, vibratory compaction roller with sheep's foot shell kit. Cleaner bar. The pre-emission (NO DEF) Cummins diesel engine starts easily and burns clean exhaust. The c ..... read more

2015 - Ingersoll-Rand SD100 Drum Compactor

Machinery Trader Group Co.,Ltd one of the biggest used construction machinery company in Shanghai china .We are specialized in used construction machine such as wheel loader, bulldozer, road roller, grader, cra ..... read more

1990 - Ingersoll-Rand R10071 Vertical Drill

1991 - Ingersoll-Rand MW175 Cold Milling

INGERSOLL RAND MW-175 MILLING MACHINE -Powered by Detroit Turbo Diesel Engine -Equipped with Hydrostatic Transmission -20in.cutting width -Water System -Pneumatic Wheels

Ingersoll-Rand LM100 Vertical Drill

2006 - Ingersoll-Rand HP915WCU Compressor

COMPRESOR DE AIRE INGERSOLL RAND HP915WCU CON MOTOR DIESEL CUMMINS QSL9 DE 6 CILINDROS

Ingersoll-Rand ECM720 Vertical Drill

CON MOTOR CATERPILLAR C12, MASTIL DE 28 FT, PISTOLA MONTALBERT HC200A, UTILIZA BARRAS DE 12X2, DIAMETRO DE PERFORACION DE 4 A 5 1/2 PULGADAS

2008 - Ingersoll-Rand ECM720 Vertical Drill

4.5 - 5.5 Inch Class* Montabert HC200A Drifter* Cat C11 Engine* Set up for 60mm drill steel Only 3570 Total Hours

2007 - Ingersoll-Rand ECM720 Vertical Drill

Montabert HC200A Drifter - '0' hours on fresh service CAT Engine Set up for 60mm drill steel Onboard Air of 480 CFM @ 150 PSI 5500 total frame hours 2012 percussion hours w/ '0' hours on new service. PRICED TO ..... read more

2007 - Ingersoll-Rand ECM720 Vertical Drill

4.5” – 5.5” Inch Class* CAT C11 Diesel Engine* HC200A Drifter set up for GT60 Rods* Caterpillar C11 Diesel Engine Montabert HC200A drifter. Recent new hydraulic Pump Aprox. 11800 total frame hours Unit is ..... read more

2006 - Ingersoll-Rand ECM720 Vertical Drill

**DRIFTER ONLY** - HC200A Drifter - Excellent condition - Very low hours since new

1999 - Ingersoll-Rand ECM690 Vertical Drill

3.5 - 4.5 Inch Class* HC200A Drifter* CATERPILLAR 3306 Diesel Engine* Extendable Boom Onboard Ingersoll-Rand 420 CFM @ 150 PSI Air Compressor Rod Changer Ready to ROCK & ROLL!

1996 - Ingersoll-Rand ECM690 Vertical Drill

4.5” – 5.5” Inch Class* CATERPILLAR Diesel Engine* YH Series Drifter* YH110V Hydraulic Drifter Set up for T51 CAT 3306 Diesel Engine Extendable Boom Rod Changer

2002 - Ingersoll-Rand ECM680 Vertical Drill

3.5” – 4.5” Inch Class* HC150 Drifter * Set up for T51* Cummins Diesel Engine

2014 - Ingersoll-Rand ECM660 Vertical Drill

3.5 - 4.5 Inch Class* HC 158 Drifter* Cummins QSL9 Diesel* Extendible boom 1430 hours Back-Up Alarm Warning Horn Accumulator Charge Kit Drifter Hour Meter Air Conditioned and Heated 2D Digital Angle Indicator A ..... read more

2011 - Ingersoll-Rand ECM660 IV Vertical Drill

3.5 - 4.5 Inch Class* HC158 Drifter* 5950 total frame hours* 844 percussion hours Overall unit is in excellent condition. Will be cleaned at time of sale.

2011 - Ingersoll-Rand ECM660 IV Vertical Drill

3.5 - 4.5 Inch Class* HC158 Drifter* Cummins Tier 3 Diesel Engine*

2004 - Ingersoll-Rand ECM660 III Vertical Drill

3.5 - 4.5 Inch Class* Montabert HC160 Drifter* Very Well Maintained Unit* 7036 Total Frame Hours 2251 Percussion Hours

2002 - Ingersoll-Rand ECM660 II Vertical Drill

3.5 - 4.5 Inch Class* HCR120 Drifter w/ 2287 Percussion Hours* Cummins Diesel w/ 5,828 Hours* Enclosed Cab w/ AC Set Up for T51 Rod Changer w/ One-Lever Control

2007 - Ingersoll-Rand ECM590 Vertical Drill

2007 Copco/IR ECM 590 • Set up for T45 • YH-80 Hammer • Good overall working condition • Currently on a job but available

2006 - Ingersoll-Rand ECM590 Vertical Drill

- Equipped with YH80A Drifter - Repairs needed or in the process of being repaired - Dust collector top new part has been fabricated need's installed - Rod changer arm is broken have new parts to replace purcha ..... read more

2005 - Ingersoll-Rand ECM590 Vertical Drill

- Equipped with YH80A - Ready to work - Repairs needed are inoperable fuel stop solenoid

2005 - Ingersoll-Rand ECM590 Vertical Drill

2005 Ingersol Rand ECM590 8.3 Cummins Engine YH80 Drifter Set Up For T45 7,228 Engine Hours 3,564 Drifter Hours $49,500 Contact for more details

2004 - Ingersoll-Rand ECM590 Vertical Drill

- Equipped with YH80A Drifter - Mechanic believes there is a broken pin in the fuel injection pump machine will idle but will not idle up. - Other repairs needed are inoperable fuel stop solenoid

2004 - Ingersoll-Rand ECM590 Vertical Drill

- Comes with YH70 not currently installed but will be mounted for transport - This unit has tracking issues will move but unknown if it's the final drives or hydraulic motors. - Hammer needs to be mounted back ..... read more

2003 - Ingersoll-Rand ECM590 Vertical Drill

- Comes with YH70, not currently installed but will be mounted for transport - Batteries need charging or replaced so could not stand machine up at time of photos. - Missing wall and doors need to be reattached ..... read more

2002 - Ingersoll-Rand ECM590 Vertical Drill

2002 Ingersoll-Rand ECM590 • Set up for T51, looking for extra rods/bits. Will confirm • Cummins Engine Rebuilt in 2017 w/ 3,098 Hours • 3,536 Drifter Hours • YH80 Hammer(Rebuilt) • EXW: New Jersey

2000 - Ingersoll-Rand ECM590 Vertical Drill

- Equipped with YH80A Drifter - Unit needs nothing is currently running on a job at this time. - Has newer paint job - Manual rod changer - Long boom

1999 - Ingersoll-Rand ECM590 Vertical Drill

- Equipped with YH80A Drifter -Only known issue is the engine Boggs down under a hydraulic pressure load everything works as intended but noticeable lack of performance due to lower engine rpm's . Possible fuel ..... read more

1997 - Ingersoll-Rand ECM590 Vertical Drill

- Equipped with YH80A Drifter - Ready to work - Repairs needed are one door with broken hinges - Fuel stop solenoid - This machine has a new air end and has less than 200 hours on hydraulic pump

2005 - Ingersoll-Rand ECM585 Vertical Drill

2.5 - 3.5 Inch Class* Montabert HC109 Drifter* Excellent Condition* Engine Hours 5416.2 Percussion has ONLY **933 Total Percussion hours since new*** HC109 Drifter was last rebuilt June 2015 – last rebuilt @ ..... read more

2002 - Ingersoll-Rand ECM580 Vertical Drill

3.5” – 4.5” Inch Class* HC80RP Drifter* Cummins Diesel Engine* Extendable Boom 8130 Engine Hours Water Injection Dust Collector Enclosed Operators Cabin Montabert HC80RP Drifter

1998 - Ingersoll-Rand ECM570 Vertical Drill

1998 Ingersoll Rand ECM570 Overall good condition relative to age Needs hose from boom to dust collector

1997 - Ingersoll-Rand ECM570 Vertical Drill

2.5 - 3.5 Inch Class* Montabert HC80 Drifter* Cummins Diesel Engine*

2000 - Ingersoll-Rand ECM490 Vertical Drill

- Cummins 6CT8.3 - Tier 2 - 200CFM/140PSI Air - YH70 Drifter - Setup for T38 - 12,667 engine hours - Drifter Rebuild @ 12,518 Hours - New feed chain & sprockets @ 12,348 hours - 1,000 hour service done @ 12,667 ..... read more